Holybro FETTEC FC G4 Stacks OSD Flight Controller

Holybro FETTEC FC G4 Stacks OSD Flight Controller 170MHz IIM-42652 W/ Tekko32 F4 50A / Matel 65A 4in1 ESC 2-6S for RC FPV Drone

• The FETtec KISS FC G4 is a flight controller running the KISS V2 firmware for high performance, simple setup. The flight controller has an onboard real-pit for TBS Unify Pro Nano VTXs and headers for direct connection to a TBS Crossfire Nano RX. The FETtec FC supports 30×30 and 20×20 mounting.

• – STM32 G4 Processor, 170MHz with IIM-42652 SPI Gyro
• – Built-in real Pit-Mode
• – Seperate onboard 5V BEC For RX
• – 5V/16V BEC for VTX
• – 20x20mm M2 and 30.5mmx30.5mm M3 mounting holes
• – 8 Native DSHOT2400 outputs
• – 4 Signal and ground pads in each corner
• – 8 pin connector for solder free FETtec ESC connection

• Designed for 6-27V supply voltage (2S-6S Lipo)
• 2x onboard BEC (max. 600mA each)
• 5V BEC for RX
• 5V / 16V BEC for VTX (configurable and real pit *)
• 5 UART serials
• Buzzer pads
• 4 tiny RGB LEDs (color selectable)
• FETtec KISS firmware

Tekko32 F4 4in1 50A ESC

F4 MCU @150Mhz / PWM output up to 96K / 4~6S / BLHeli32 / 30×30
The all new Tekko32 is the first 4in1 ESC in market to adapt the fast F4 MCU 150Mhz, providing a smooth control operation and quick response.

Features:
New & faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
PWM output up to 96K (default 48K)
Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

Specification:
Continuous Current: 50A x4
Burst Current: 60A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 168
Dimensions: 45x37x6mm / Weight: 13.8g
Mounting holes: M4 30.5×30.5mm (M3 grommets included)

Tekko32 F4 Metal 4in1 65A ESC

F4 MCU @150Mhz / Metal-Cased MOSFET / PWM output up to 96K / 4~6S / BLHELI32
The all new Tekko32 Metal is the first 4in1 ESC in the market to adapt the fast F4 MCU. Powerful & reliable metal-cased MOSFET 4in1 ESC with smooth control and quick response.

Features:
New & faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
PWM output up to 96K (default 48K)
Metal-cased MOSFET for excellent heat dissipation
Massive on-board capacitance for noise filtering at 2068uf
3 oz copper PCB design to allow bigger current and better heat dissipation
Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

Specification:
Continuous Current: 65A x4
Burst Current: 75A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 168
Dimensions: 43 x 44mm / Weight: 15.8g
Mounting holes: M4 30.5×30.5mm (M3 grommets included)

Notice:
The air flow is very important if you want to run this 4in1 in high current.
The input cable (from Lipo to 4in1) should be at least 12AWG and well soldered.